'Second' p2 Searchterm 'Second' found in 3 terms [ • ] and 26 definitions [• ]Result Pages : •
A lower orbited electron leaves the atom - the reoccupation of this vacancy by a higher orbited electron leads to the emission of energy which in turn leads to the emission of a second electron, the Auger electron. See also Auger Electron, Electron Excitation, Megaelectron Volt and Auger Pierre Victor. •
(Bq) Becquerel is the system international (SI) since 1985 new unit of radioactivity. 1 becquerel is equal to 1 disintegration per second. 1 Bq = 0.027 x10-9 Ci (Curie). In medicine and radiation protection the SI measurement units of becquerel, gray and sievert (should) have replaced the conventional units of curie, rad and rem. To convert: See also Gray, Sievert, Roentgen Equivalent In Man, Radiation Absorbed Dose, Count and Becquerel Antoine Henri. •
A cinefluorography produces a movie (cine) film from an image intensifier during x-rays examinations (often called videofluorography, cineradiography or cine). Cinefluorography is always monitored on the TV screen normally used for fluoroscopy. The image from the output screen of the image intensifier is split with a semi-transparent mirror into two output ports; one leading to the movie camera and the other to the fluoroscopy camera. Most of the light is directed to the cine camera. The image on the monitor does not suffer in quality due to the fact that the tube current for cinefluorography is about 100 times higher than for common fluoroscopy. The x-ray generator pulses are synchronized with the movements of the cine camera, so that no x-rays are emitted when the film is moved forward to the next frame. The needed very accurate synchronization of the x-ray generator can be achieved by use of high voltage switching in the secondary circuit of the constant potential x-ray generator, by starting and stopping the inverter in a medium frequency generator or by using a grid controlled x-ray tube. ![]() Further Reading: News & More:
• The clearance is the elimination
of substances like drugs, chemicals and secondary products from the body. Although clearance may also involve other organs than the kidney, it is almost synonymous with renal clearance or renal plasma clearance. Each material has a specific organ clearance that depends on its filtration characteristics.
•
Contrast media injectors are part of the medical equipment used to deliver fluids in examinations such as CT, MRI, fluoroscopy and angiography. Many of these diagnostic imaging procedures include the administration of intravenous contrast agents to enhance the blood and perfusion in tissues. Mainly there are two types of injector technology: •
Piston-based systems use a plunger/piston to move a piston in the cylinder of a reservoir, which works in two directions
to first fill the reservoir and then deliver the fluid from the reservoir to the patient, similar to a hand-held syringe.
•
Peristaltic-pump-based systems operate as rotary pumps that use rollers to compress sections of flexible tubing, drawing fluid directly
from the supply source and delivering it to the patient.
See also Single-Head Contrast Media Injector, Dual-Head CT Power Injector, Syringeless CT Power Injector. The use of x-ray contrast agents in computed tomography (CT) began with a hand injection by the radiologist in the scan room. During its history, CT scanners have made great improvements in speed and image quality. Actual CT systems with multiple detectors allow scan times of a few seconds per body region. Some CT protocols require multiphase scans, where a body region is imaged with a single bolus of contrast in different blood flow phases. Automatic power (pressure) contrast media injectors are required to provide precise control of flow rate, volume and timing of injection. The use of a saline bolus following contrast administration reduces the volume of contrast required. Most relevant topics for the use of a power injector in medical imaging procedures such as contrast enhanced computed tomography (CECT): •
Avoidance of microbiologic contamination;
•
workflow efficiency in the use of the contrast media injector;
•
contrast cost and waste volume;
•
reimbursement.
Must have basic injector control options: •
Flow rate with a usual range from 0.1 to 10 mL/sec in 0.1 mL/sec increments; some injectors can be set to inject in ml/min or
ml/hour;
•
pressure limit typically programmable from 50 psi to 300 psi in 1 psi increments
(also displayable in kPa and kg/cm²).
Examples of other injector control options: •
•
pre-filled syringes; the compatibility with many selected syringes makes it easy to change and select the appropriate contrast medium for each patient;
![]() Further Reading: Basics:
News & More:
Result Pages : |